Osculati

Nautical socket for 32A - 220V shore power cable. Made of PA6, equipped with high energy efficiency contacts and an IP67 closure cap. The plug is designed to ensure an ergonomic grip, and the rotating ring allows it to be securely fastened to the boat's socket with an IP67 watertight seal, while the rubber cap ensures an IP44 seal when not connected. The clean design and compact dimensions allo... read+

Complete 220V boat power supply set for dock charging column. The kit includes the Cruiser electrical outlet for installation on the boat, wired electrical panel 16A with lifesaver, circuit breaker, schuko outlet, 3G wiring of 3 m and cable of 10 m to connect to the power column. The system is available in four different layouts to choose the socket that best suits the hull color. The dock exte... read+

Complete 220V boat power supply set for dock charging column. The kit includes the Cruiser electrical outlet for installation on the boat, wired electrical panel 16A with lifesaver, circuit breaker, schuko outlet, 3G wiring of 3 m and cable of 10 m to connect to the power column. The system is available in four different layouts to choose the socket that best suits the hull color. The dock exte... read+

Complete 220V boat power supply set for dock charging column. The kit includes the Cruiser electrical outlet for installation on the boat, wired electrical panel 16A with lifesaver, circuit breaker, schuko outlet, 3G wiring of 3 m and cable of 15 m to connect to the power column. The system is available in four different layouts to choose the socket that best suits the hull color. The dock exte... read+

Reference Amperage Cable length Outer cable diameter  Cable section Dock socket 14.416.08 10 A 10 m 7.9 mm 1.5 mm² No 14.416.18 14.335.01 (16 A) read+

Pre-wired pushpull connector for 14.315.xx flat switches. Simplifies wiring of 14.315.XX switches, 12/24V operation. Jumper cable for “Push ON” or “Always ON” LED configuration. • Cable length: 15 cm. • Fastening ring to prevent accidental cable disconnection. Code 14.315.20 is compatible with single LED switches, while code 14.315.21 is compatible with RBW LED switches. read+

• Facilitates wiring of the 14.315.XX switches. • Includes an auto-reset circuit breaker. Jumper wire allows LED configuration as “Push ON” or “Always ON”. • Cable length: 15 cm. • Locking ring prevents accidental cable disconnection.   Reference Capacity 14.315.31 5 A 14.315.32 10 A 14.315.33 15 A 14.315.34 20 A read+

FLAT anti-vandal switch with AISI 316 stainless steel body manufactured by CNC. • Compatible with 12V and 24V systems and rated at 20A. • Protection rating IP67. • LED light ring available in 3 different colours. • Can be installed on surfaces with a maximum thickness of 8 mm. *Sold individually   Reference Colour 14.315.05 White 14.315.06 Red 14.315.07 Blue read+

Accessory for wireless engine cutoff switch. Ref. 14.968.02   read+

Rear protection cover for Berker frames.• White color.  Reference Depth Suitable for modules 14.538.01 22 mm 14.520/521/522/523/524 14.538.02 45 mm 14.525/526/527.01 read+

Spacer that allows mounting Berker 14.520/521/522/523/524 modules without recessing them.  Reference Color 14.538.03 Black 14.538.04 White read+

• Operates on a wide voltage range from 5V to 24V DC.• Used in combination with switches 14.523/14.524.xx or similar to adjust the brightness of ceiling lights/spotlights, either incandescent or LED (if compatible).• Maximum load 192W (at 24V) read+

Bulb for general-purpose headlights with lamp holder, 36 mm pin spacing.• Equipped with LED with 360º total irradiation.• 12 V• 2 Units   Reference Length LED Chip Consumption Light Color Temp. 14.300.33 36 mm 8 24 2 W 180 lm 3000 K read+

Bulb for classic headlight 12 / Utility 85 / Utility 77.• Equipped with LED with 360º total irradiation.• 12 V• 2 Units   Reference Length LED Chip Consumption Light Color Temp. 14.301.23 39 mm 12 24 2.5 W 250 lm 3000 K read+

Self-priming with neoprene impeller and thermal protection against overload, with automatic reset. Permanent magnet motor. • Version A: brass body with stainless steel base. • Version B: thermoset resin body with stainless steel bases.   Item Version Voltage Maximum flow rate Head Consumption Self-priming Hose connection Replacement impeller 16.197.12 A 12 V 26 l/min 7.5 m 9.9 A ... read+

Dual mounting option: on wall or with bracket. Possibility to mount the ventilation hose both on the inlet and on the outlet. Anti-corrosion ABS housing. Complies with CEI EN50014-1 and N61000-3-3 standards for electric motors operating in potentially explosive environments. • Voltage: 12V • Flow rate: 220 m³/h • Current draw: 2.5 A • Outlet: Ø 76 mm • Dimensions: 160 x 160 x 196 mm • Optional... read+

Fastening with two screws on panels 6-16 mm thick, complete with snap closure. • Material: nylon and stainless steel. • Dimensions: 63 x 63 mm • Hole in base: 50 mm • Stop travel: 27 - 50 mm read+