Shaft Line Systems

● Shaft line bushing made of rubber Ref.: Ø A Ø B C 52.207.22 22 mm 29 mm 75 mm 52.207.23 22 mm 36 mm 80 mm 52.207.25 25 mm 36 mm 100 mm 52.207.26 25 mm 40 mm 120 mm 52.207.30 30 mm 40 mm 120 mm 52.207.35 35 mm 54 mm 140 mm 52.207.40 40 mm 54 mm 140 mm   read+

● The clamp system enables to install the cutter without disassenbling the propeller Ref. Ø axis mm A Ø outer mm B Thickness mm 52.961.01 25 80 22 52.961.03 30 80 22 52.961.04 31.75 (1" 1/4) 80 22 52.961.05 35 100 22 52.961.07 40 100 22 52.961.08 44.5 (1" 3/4) 120 22 52.961.09 45 120 22 52.961.10 50 120 22   read+

Long lasting insulation from water seepage, low maintenance required if correctly treated. Made of a special type of rubber resistant to salt water and lubricating grease. The product is supplied with an AISI316 stainless steel clamp and specific lubricant for shaft line. Operation of the stuffing box is usually under the waterline; lubrication and cooling by water. In case of operation above o... read+

● Made of hydro-lubricating rubber. ● Shaft line bushings with external brass frame. ● External / internal version in millimeters   Ref Ø A mm Ø inches  B mm Ø C mm 52.307.20 20 mm 31,75 (1”1/4) 76,2 mm 52.307.22 22 mm 31,75 (1”1/4) 76,2 mm 52.307.25 25 mm 38,1 (1”1/2) 101,6 mm 52.307.26 25 mm 31,75(1”1/4) 101,6 mm 52.307.28 28 mm 41,27 (1”5/8) 114,3 mm 52.307.30... read+

 Shaft line bushings with brass external frame. External/internal version in millimetres Made of hydro-lubricating rubber.   Ref Ø A mm Ø B mm Ø C mm 52.308.20 20 mm 30 mm 80 mm 52.308.25 25 mm 35 mm 100 mm 52.308.26 25 mm 40 mm 100 mm 52.308.28 28 mm 38 mm 112 mm 52.308.30 30 mm 40 mm 120 mm 52.308.31 30 mm 45 mm 120 mm 52.308.32 32 mm 45 mm 128 mm 52.308.35 ... read+

● Rubber-polyurethane coating inside ● Brass on the outside ● Bearings with Shaft dimensions (A) in mm and outside (B) in mm. Length (C) in mm   Brass A B** C RULAGER25 25 1 1/2 100 RULAGER30 30 1 3/4 120 RULAGER35 35 1 7/8 140 RULAGER40 40 2 1/8 160 RULAGER45 45 2 3/8 180 RULAGER50 50 2 5/8 200 RULAGER60 60 3 240 RULAGER70 70 3 1/2 280 RULAGER80 80 4 32... read+

● Rubber-polyurethane coating inside● Brass on the outside● Bearings with Shaft dimensions (A) in mm and outside (B) in mm. Length (C) in mm   Brass A B C RL2540 25 40 100 RL3045 30 45 120 RL3550 35 50 140 RL4055 40 55 160 RL4565 45 65 180 RL5070 50 70 200 RL6080 60 80 240 RL7090 70 90 280 RL8010 80 100 320 RL9011 90 110 360 RL1012 100 125 400   read+

ZWBH seals are developed for use with water lubricated stern gear. This updated monoblock design works in the same way as the trusted ZWB seals, with the addition of one extra lip seal (three total) for added security. • ZWBH seals can withstand temperatures between -15º and +85º and are suitable for Vetus bronze, steel or GRP stern tubes. • Minimal friction, oil and grease resistant... read+

● Made with long fibers in mixed cotton hemp and teflon with square sections to provide water-tightness on the propeller's box shaft. ● For correct operation make sure that the packing is mounted in short slugs that form just one ring each. ● Length: 2 metros. Reference Diameter mm For bearing diameter (mm) is 52.190.06 6 18/25 52.190.08 8 25/35 52.190.10 10 40/60 read+

● Prevent the lines from getting stuck between the rubber bushing and the line cutter. ●  It is an AISI type 316L stainless steel circular saw blade that is placed behind the helix. ● They are separated into two parts ●  Shaft cutter Referencia Dimensions  (mm) Medida del eje (mm) VRC25 115 x 30 25 VRC30 115 x 30 30   read+