Skip to content
I have bought other times here
I'm already a customer
I want to register
New customer
By creating an account at francobordo.com you can make your purchases quickly in our virtual store, check the status of your orders and check your previous operations.

Ahead! We were waiting for you.
Create an Account
Access the
Professionals Area

Register and take advantage of the discounts and advantages of being a Professional of Nautical

Join the more than 500 Nautical Professionals now

professional register
Black Friday · Easysea & Garmin
Victron Energy Quattro 24/5000/120 100-100

Victron Energy Quattro 24/5000/120 100-100

Ref.: QUA245023110
2.364,00 €
VAT included
Delivery in 7-10 days
Buy now and receive it between Wednesday 2 of December and Monday 7 of December.

* Except the products on request that depend on the receipt of the same.(+ info.)

Product description

The Quattro is an inverter/charger of Victron Energy compatible with Lithium-Ion batteries. It has two AC outputs with an integrated transfer switch: it can be connected to two independent AC power sources (for example, the shore power inlet, a generator or two generators) and will connect automatically to the active power source.

Photo for guidance

Two AC outputs

The main output has the «no-break» function (without interruption). The Quattro takes care of supplying the connected loads in the event of a power cut or disconnection of the mains/generator. This happens so quickly (less than 20 milliseconds) that computers and other electronic equipment continue to operate without interruption.

The second output is only active when one of the Quattro's inputs has AC power. Appliances that should not discharge the battery, such as a water heater, for example, can be connected to this output.

Virtually unlimited power thanks to parallel operation

Up to 6 Quattros can operate in parallel to achieve a higher output power. Six units 48/5000/70, for example, will give an output power of 27kW/30 kVA and a charging capacity of 420 amperes.

Three-phase operation capability

In addition to parallel connection, three units of the same model can be configured for a three-phase output. But that is not all: up to 6 sets of three units can be connected in parallel and will provide an output power of 81kW / 90 kVA and more than 1260 amperes of charging capacity.

Split-phase options

Two units can be stacked to obtain 120-0-120V and up to 6 additional units per phase can be connected in parallel to supply up to 30kW / 36kVA in split phase. A split-phase AC source can also be obtained by connecting our autotransformer to a «European» inverter programmed to supply 240V/60Hz.

PowerControl: limited power from the generator, the shore power inlet or the mains

The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or the pontoon mains (nearly 40A for each Quattro of 5 kVA at 120 VAC). A maximum current from the generator or the pontoon can be set. The Quattro will take care of other AC loads and use the surplus current for charging, thus preventing the generator or the shore power inlet from being overloaded.

PowerAssist: boosting the electrical capacity of the shore power inlet or the generator

This function takes the PowerControl principle to another dimension. It allows the Quattro to supplement the capacity of the alternative source. When a power peak is required for a short period of time, as often happens, the Quattro will immediately compensate for the possible lack of power from the mains or generator current with power from the battery. When the load is reduced, the surplus power is used to recharge the battery.

Solar energy: AC power available even during a power cut

The Quattro can be used in PV systems, grid-connected or not, and in other alternative electrical systems.

System configuration could not be simpler

Once installed, the Quattro is ready to operate. If the configuration has to be changed, it can be done in a matter of minutes using a new DIP switch configuration procedure. With the DIP switches, parallel and three-phase operation can even be programmed: without the need for a computer!

In addition, a VE.Net can also be used instead of the DIP switches.

And sophisticated programs are available (VE.Bus Quick Configure and VE.Bus System Configurator) to configure several new and advanced features.

Technical specifications

Be the first to leave your opinion
0/5
5 stars
0%
4 stars
0%
3 stars
0%
2 stars
0%
1 stars
0%
Write your opinion about this product
 
Select your language: