Mercury

● Original gasket for drian oil screws, verado 4 and 6 cylinder enginers.   Read more »

● Mercury Propeller Black Max Step 10.4x13´   [list_down title="Product Specs"] ● 13 tooth spline ● Diameter: 10.4´´ ● Pitch: 13´´ ● No. of blades: 3 ● Material: Aluminum [/list_down]   [list_down title="In the box"] ● Flo-Torq Reflex Hub Kit 835257K12 included with Reflex Propeller Sleeve with part number 8M0047148 [/list_down]   [list_down title="Compatible enginer"] ● 25 hp Bi... Read more »

● Contains a drying commonly used to keep small, sealed containers dry. ● It absorbs the water that has accumulated in the fuel tank. ● Use mode: Attach to the inner fuel cap with the cord (included). Adjust the lanyard so that the water elminator sits on the bottom of the fuel tank. Replace as needed. ● For use in all octane grades of gasoline, including blended ethanol. Not recommended for di... Read more »

● Water separating fuel filter with blue screw-on sensor. ● Located under the hood of all 1996 and newer Mercury/Mariner V-6 EFI/DFI outboards. Read more »

● Mercury faceplate compatible with the next enginers:   75/90 HP 65 JET (3 CYLINDER) - 65 JET (3 CYL.) 200/225 (3.0L)(MECHANICAL) - 225 (DFI) 3.0L 225 SPORT XS DFI (3.0L) - 225 SPORT XS (3L) 200/225 (3.0L DFI) - 225 (DFI) 75/80/90/100/115 EFI 4-STROKE - 100 EFI (4-STROKE) 55/60 JET 40 (3 CYLINDER) - 40 JET 225XS / 225 SPORT XS DFI (3.0L) - 225 SPORT XS 200/250... Read more »

● Gasket set Mercruiser 27-17145 Read more »

● For outboards enginers of 75-125 CV. ● For Mercury enginers fourstroke: ● 40, 50 , 60 CV (1995 +) ● 75, 90 , 115 cv. ● For Mercury enginers 2 stroke: ● 40, 50, 60 CV ● 65, 75, 90 CV ● 80, 85, 100, 115, 125, 140 CV ● Diameter: 13.3 ● Pitch: 17" ● Right hand rotation Read more »

● Mercury Mariner Impeller for outboard engines 15 / 20 HP  ● Shaft dimensions: 13.85 mm ● Impeller diameter: 41 mm ● Width: 23.50 mm ● Number of blades: 8 Read more »

● Mercruiser power trim e-ring for Alpha One Gen 2 models.   Read more »

● Pump Bracket for Mercruiser Trim Read more »

● Mercury marine gasket set with fits 2 bbl mercruiser mercarb carburetors with hooked (bent) accelerator pumps. ● For Mercruiser 3.0L, 4.3L, 5.0L y 5.7L engines. Read more »

● Mercruiser water pump face seal fits Alpha one gen II water pump Housing Read more »

● Mercruiser 100 hou maintenance kit for Alphe one gen II sterndrive (1991&newer) S/N 0D469859 & above. ● Kit includes: ● 1 drive installation gasket kit ● 1 anode kit ● 2 gear-case drain seals. Read more »

● This control has a trim switch on the port handle and includes the trim wire harness (attached to the switch) with the white connector. ● All installations require and ignition/choke harness and throttle/shift cables to complete the installation. ● Compatible for the next engines: ● All 1993 and later Mercury/Mariner integrally trimmed and Force 40HP and higher outboards using Mercury-style p... Read more »

● Mercury - Flo-Torq II Transmission Bush Read more »

● For less 250 HP outboard engines ● 15 ¼" Diameter ● 15" Pitch ● Right Hand Rotation ● 3 high-quality die cast aluminum blades ● Attractive and durable high-gloss Phantom Black finish ● Easy to maintain & repair. Read more »

● Mercruiser 864493 thermostat is compatible for the next mercruiser enginers: ● 4.3 MPI Alpha/Bravo ● 4.5L MPI ● 350 MAG MPI Alpha/Bravo ● 357 HRZ ● 377 MAG MPI ● 5.0L MPI Alpha/Bravo ● 5.7L MPI ● 6.2L MPI ● 77º C - 170º F thermostat. Read more »

● Mercruiser type 3 alternator with 6 serpentine, 65 mm. ● Volts: 12V ● Amps: 70A ● Compatible with the next models: ● MERCRUISER Modelo 5.7L EFI (Gen +) GM 5.7L - 350ci - 8cyl 98-On ● MERCRUISER Modelo 5.7L EFI (Gen +) MIE GM 5.7L - 350ci - 8cyl 97-On ● MERCRUISER Modelo 5.7L MIE GM 5.7L - 350ci - 8cyl 99-On ● MERCRUISER Modelo 7.4L MIE MPI (L29) (Gen VI... Read more »

● Alternator Mercruiser with internal regulator. ● Volts: 12V ● Amps: 55A ● Compatible with the next models: ● MERCRUISER 4.3 V6 since 1992 to 1998. ● Volvo enginers 3.0, 4.3, 5.7, 7.4, 8.2, 5.0 y 5.8. Read more »

● Mercruiser 65A alternator valid for Mercruiser 3.0L inboard or stern drive enginers (seriel number 0M326296 to 2A506300) Read more »

● Mercury water pump repair kit 812966A12. ● Repair kit includes impeller, gasket, wear plate, upper pump casing, lower pump casing, waterline, and o-rings along with other small gaskets. ● Enginers compatibles: ● 40-60 HP ● 40/50/60 HP EFI ● 50/60 HP CARB standard 4-stroke. ● Mercury mariner 50, 55, 60 HP (3-CYL) (2 stroke). Read more »

● Alpha One II prop nut kit that include two star style tab washers and one nylon nut. ● Compatible for the next models: ● 90-115HP Command Thrust 2014 y posteriores. ● 135HP 1987 and newer. ● 150HP 1978 and newer. ● 175HP 1978 and newer. ● 200HP 1978 and newer ● 200HP 1987-1988 ● 225HP 1980 and newer. ● 225HP (Sea Pro/Marathon) ● 250HP 199... Read more »

● Replacement cable kit compatible for Bravo models. Read more »

● Oil fitting manufactured by Mercury and compatible with the next models: ● 100 vazer ● 3.0L Alpha One ● 3.0L GM 181 inline-4 ● Alpha One (Gen II) 1998 y posteriores ● Bravo One ● Bravo tres ● Bravo Dos ● Bravo x uno ● Bravo x tres ● Bravo x dos ● Bravo XR I Sport Master ● Bravo XR II Sport Master ● Bravo XR III Sport Master... Read more »

● Quicksilver Serpentin strap 134,6 cm long ● Compatible for the next engines: ● 5.0L, 350, 377 MAG MPI STERNDRIVE EC - 350 MAG MPI ALPHA/BRAVO EC ● 5.0L, 350, 377 MAG MPI STERNDRIVE EC - 5.0L MPI ALPHA/BRAVO EC ● 5.0L, 350, 377 MAG MPI STERNDRIVE - 350 MAG MPI ALPHA/BRAVO ● 5.0L,350 MAG,MX 6.2L MPI STERNDRIVE - MX 6.2L MPI HORIZON BRAVO ● 5.0L, 350, 377 MAG MPI STERNDRIVE EC - 350 MAG MPI HO... Read more »

● Bravo transom hose kit 8M0090859 include: ● Hose assembly ● Rubber bushing ● Bushing retaining tool ● Water inlet housing gasket. ● 2 screws ● Hose end insert ● 2 water inlet housing Read more »

● Mercruiser thermostat housing to circulation pump water hose. ● Compatible with 2.5L, 3.0L,120,140 and 165 engines. Read more »