Specials

Compatible Devices:  GSD 24     read+

    Unit dimensions, WxHxL: 31/32" x 43/64" x 3 3/32" (24.7 x 17.0 x 78.6 mm)   Total cable length: 16 ft. (4.9 m)   Temperature range: From 5°F to 158°F (from -15°C to 70°C)   Compass Safe Distance: 2 in. (5 cm)   Power Input Source: 9–16 Vdc from the NMEA 2000 bus   NMEA 2000 Power Usage: 1.1 W max   NMEA 2000 Load Equivalency Number (LEN): 2 (100 mA) ... read+

● Our bronze thru-hull mount transducer offers good performance at high speeds. ● An excellent selection of fiberglass and wood hulls, this 600W 8-pin narrow bore transducer has a depth of 800m to 1,200ft, an operating frequency of 50 to 200kHz, a beam of 45 to 12 degrees and a strut angle between 0 and 7 degrees. ● The transducer kit is supplied with installation instructions. ... read+

♦ Skimmer Stern in-Hull or engine mounting ♦ 83/200 kHz ♦ Blue connector ♦ Only depth read+

♦ Skimmer Stern with internal temperature sensor mounting. ♦ 50/200 kHz ♦ Blue connector read+

♦ Simrad Blue connector temperature sensor (not connected to network) read+

● Transducer 1 kW 8 pines mid-range narrow beam transducer is ideal for deep water and bottom definition. Main Features: ● Deep: 1500 to 2200 ft ● Operating frequency: 50 to 200 kHz ● Beam: 14 x 23 to 3 x 5º ● Stanchion angle of between 0 and 26º degrees   read+

● Transducer 1 kW 8 pines mid-range narrow beam transducer is ideal for deep water and bottom definition. Main Features: ● Deep: 1800 to 2500 ft ● Operating frequency: 50 to 200 kHz ● Beam: 19º / 6º ● Stanchion angle of between 0 and 20º degrees read+

  With Garmin’s NMEA 2000 Engine Tilt/Trim Analog Adapter aboard your vessel, you can give new life to your old gauges by making the transition from analog to digital. This simple-to-install adapter takes the data generated by traditional analog gauges and converts the data into a NMEA 2000 signal so you can create or expand your network without replacing all of the equipment on your boat.... read+

● HDI Skimmer transducer 83/200/455/800kHz with built in temp. ● Includes mounting bracket and hardware read+

● Backbone required to install one or more NMEA 2000 sensors with any HDS install; includes power cable, 2-ft cable, 15-ft cable, 2 x T-connector, network terminators read+

● HDI Trolling motor adaptor for Skimmer (*only for 83/200/455/800 HDI Skimmer transducer) read+

  With Garmin’s NMEA 2000 Fluid Level Analog Adapter aboard your vessel, you can give new life to your old gauges by making the transition from analog to digital. This simple-to-install adapter takes the data generated by traditional analog gauges and converts the data into a NMEA 2000 signal so you can create or expand your network without replacing all of the equipment on your boat. &nbs... read+

This plastic transom mount can be used to replace the dual frequency transducers included with many Garmin units.   The 500 W 8-pin transducer has a maximum depth of 1,500 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 40 to 10 degrees; and mounts on a 0 to 70 degree transom.   Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging ... read+

● 10ft (3m) extension cable for LSS-1, LSS-HD, xSonic HDI, ForwardScan, and TotalScan transducers. *For optimum performance do not use more than 1 extension per installation. read+

● Built in temperature ● 83/200 kHz Skimmer transducer read+

● Mounting bracket over electric motor for transducers standard Skimmer read+

● Lowrance QRB-5 mount for models Mark-5, Elite-5, Elite 4 and Elite 4x read+

● Lowrance Cigarette plug power cable CA-2 for X-50DS, X-67c, M-68c, X-96 and Airmap 2000 read+

  With Garmin’s NMEA 2000® Trim Tab Analog Adapter aboard your vessel, you can give new life to your old gauges by making the transition from analog to digital. This simple-to-install adapter takes the data generated by traditional analog gauges and converts the data into a NMEA 2000 signal so you can create or expand your network without replacing all of the equipment on your boat.  ... read+